Evaporation retardant for concrete

What is a concrete anti-evaporation product?

A concrete anti-evaporation product (also known as a curing compound or curing product) is a film-forming additive applied to the surface of fresh concrete immediately after finishing. It forms a thin film that reduces the evaporation of mixing water during the first hours of curing, helping to limit plastic shrinkage and surface microcracks.

Curing is an important stage in concrete production: excessive water loss can compromise cement hydration and affect final strength and durability. An anti-evaporation product is a practical solution, especially in critical environmental conditions such as wind, heat, and low humidity.

Types of anti-evaporation products

Type Base Application Notes
Acrylic wax in aqueous solution Acrylic and water Spray or roller Low VOC emissions; check product performance and compatibility
Paraffin wax Paraffin and solvent Spray Good efficiency; may require removal before subsequent treatments
Acrylic resin in solvent Acrylic and solvent Spray More resistant film; assess use based on weather and application cycle
Water-based products Acrylic polymers and water Spray or roller Reduced emissions; suitable when the system is compatible with the intended use

Mechanism of action

Applied to the surface of fresh concrete, the anti-evaporation product forms a continuous film within a few minutes that:

  • can significantly reduce water evaporation during the first 24 hours, depending on the product and environmental conditions;
  • helps maintain the moisture necessary for cement hydration;
  • helps limit plastic shrinkage and surface cracks;
  • can improve surface strength and reduce dusting;
  • protects against surface contamination during the first few hours.

When to use an anti-evaporation product

An anti-evaporation product can be particularly useful when one or more of the following conditions occur:

  • Temperature above 25 °C with low relative humidity;
  • Wind speed above 10 km/h over the poured surface;
  • Direct sunlight on the surface;
  • large-area pours, such as floors, slabs, and yards;
  • high-performance concrete (HPC/UHPC) with a low water/cement ratio;
  • pours carried out in summer or in ventilated environments.

Product: Curing P

Pigment Al's Curing P is an anti-evaporation product in aqueous solution. It forms a flexible, biodegradable film designed to promote curing. Compatibility with primers, resins, and screeds should be verified based on the chosen finishing cycle.

Parameter Indicative value
Base Acrylic in aqueous solution
Appearance Milky white liquid
Density Approximately 1.0 kg/L
pH 8–10
Water retention efficiency ≥80% according to the technical data provided, to be verified on the updated data sheet
Coverage 4–6 m²/kg per coat
Film formation time 15–30 minutes at 20 °C
Application temperature +5 °C / +35 °C

Application method

  1. Apply immediately after finishing the concrete surface, once the bleeding water has disappeared.
  2. Spray evenly using a low-pressure pump or a short-nap roller.
  3. The indicative coverage is 4–6 m²/kg per single coat.
  4. In critical conditions, such as strong wind or intense heat, consider a second cross coat.
  5. Do not apply to wet surfaces or where bleeding water is still present.
  6. Do not apply at temperatures below +5 °C or above +35 °C.

Compatibility with subsequent treatments

Water-based Curing P may be compatible with various subsequent treatments, including epoxy primers, polyurethane resins, and screeds. Always check compatibility with the finishing system supplier. Paraffin-based or solvent-based curing compounds may require mechanical removal before applying primers or adhesives.

Anti-evaporation products and high-performance concrete

In HPC and UHPC with a low water/cement ratio, the amount of water available for hydration is reduced. Water loss through evaporation can compromise final performance; therefore, an anti-evaporation product can be an important part of the curing cycle, often used together with prolonged wet curing. The choice should be determined based on the formulation and placement conditions.

Precautions and storage

  • Store at temperatures between +5 °C and +30 °C, protected from frost.
  • Agitate before use.
  • Do not dilute with water unless otherwise specified on the technical data sheet.
  • Avoid contact with eyes and skin; use appropriate personal protective equipment.
  • Dispose of in accordance with local liquid waste regulations.

FAQ — Frequently Asked Questions

What is a concrete anti-evaporation product?

It is a film-forming product applied to the surface of fresh concrete to reduce the evaporation of mixing water during curing, helping to limit plastic shrinkage and surface microcracks.

When should the anti-evaporation product be applied?

Immediately after finishing the concrete surface, once the bleeding water has disappeared. In critical conditions, such as wind or heat, it should be applied as soon as possible according to the product instructions.

Is the anti-evaporation product compatible with subsequent treatments?

Water-based products such as Curing P may be compatible with primers and resins, but compatibility must be verified for the specific cycle. Paraffin-based or solvent-based products may require mechanical removal.

What is the coverage of Curing P?

The indicative coverage is 4–6 m²/kg per single coat. In critical conditions, a second cross coat may be considered after verifying the technical instructions.

Is an anti-evaporation product mandatory for HPC concrete?

In HPC and UHPC mixes, an anti-evaporation product can be particularly important for limiting water loss, but the curing cycle must be determined based on the formulation, environmental conditions, and the instructions of the responsible technician.

Contact us for technical information and quotes.

Application of an anti-evaporation product on the surface of fresh concrete