Deflasher for Striped Lighters: GENERAL GUIDE TO DEFLASHER

What are formwork release agents?

Formwork release agents, also known as stripping aids, are chemical products applied to the surfaces of formwork before pouring concrete to facilitate the release of the concrete element when stripping the formwork. A good release agent ensures perfect surfaces, protects the formwork from wear, and reduces working time on site.

They are available in three main versions: for 15–18-hour stripping, for immediate stripping, and for use on polyurethane elastomer, plaster, or polystyrene molds.

Why use a professional release agent?

Using professional release agents instead of improvised solutions such as oil or diesel fuel offers numerous advantages:

  • Perfect surfaces: they eliminate air bubbles from the contact surface, ensuring smooth, defect-free concrete elements.
  • Environmentally friendly: formulated with recycled mineral or vegetable oils and eco-friendly synthetic emulsifiers, they are solvent-free and do not pollute.
  • Formwork protection: they do not rust metal formwork or degrade wooden formwork or composite materials.
  • Economical: they do not stain the concrete elements or leave non-stick residues on the concrete.
  • Versatile: suitable for application on any type of formwork and surface.

Composition and mechanism of action

Release agents are composed of recycled mineral or vegetable oils and eco-friendly synthetic emulsifiers or natural micro-waxes, and are solvent-free. After application, they deposit a very thin non-stick layer on the formwork that facilitates stripping without leaving residues on the concrete.

Types of release agents

Mineral oil-based release agents

Ideal for iron, wood, and plywood formwork. They offer excellent formwork protection and clean stripping. Suitable for standard pours with stripping times of 15–18 hours.

Natural wax-based release agents

Formulated with natural micro-waxes in an aqueous emulsion. They are the eco-friendly choice for architectural concrete and exposed surfaces: they do not leave halos or stains on the concrete element.

Release agents for special molds

Specific to polyurethane elastomer, plaster, and polystyrene molds. They ensure perfect release even on complex geometries without damaging the mold material.

Release agents for immediate stripping

For fast production cycles such as industrial prefabrication. They allow release in very short times without compromising surface quality.

How to apply the release agent

It is preferably applied by spray using pumps equipped with a fan nozzle at a pressure of 3–6 bar. It can also be applied with a brush or roller in a thin, even layer. Allow the water to evaporate completely before pouring.

Compatible surfaces

  • Iron and steel
  • Planed or rough wood
  • Phenolic plywood
  • Cement
  • Polyester and polyurethane
  • Plaster and polystyrene

Consumption

Coverage ranges from 80 to 150 g/m², depending on the porosity and configuration of the surfaces. More porous surfaces require larger quantities; smooth surfaces use the minimum values.

Practical tips

  • Do not apply to wet surfaces or at temperatures below 5°C.
  • Shake the product well before use, especially for aqueous emulsion formulations.
  • Store in a cool place away from frost.
  • For very porous formwork, apply a second coat after the first has been absorbed.
    Release agent for concrete formwork and molds

Frequently asked questions about formwork release agents

What is a formwork release agent and what is it used for?

It is a product applied to the formwork before pouring to facilitate the release of the concrete element during stripping. The choice should be based on the formwork material, the production cycle, and the required finish.

What is the consumption of the release agent per square meter?

The guide indicates a consumption of 80–150 g/m², depending on the porosity and configuration of the surface. Check the consumption in the technical data sheet of the chosen product.

How do you apply the release agent?

The guide indicates application by spray with a fan nozzle at 3–6 bar, or with a brush or roller in a thin, even layer. For aqueous formulations, allow the water to evaporate before pouring, according to the product instructions.

Is the release agent compatible with polyurethane and plaster formwork?

There are specific formulations for polyurethane elastomer, plaster, and polystyrene molds. Not all release agents are interchangeable: check the product's compatibility with the mold material.

What is the difference between mineral oil-based and natural wax-based release agents?

The guide distinguishes mineral oil formulations for standard formwork and natural micro-wax formulations in an aqueous emulsion for exposed surfaces. The choice depends on the formwork, stripping cycle, and desired finish.